The performance characteristics and operation precautions of pneumatic chopper type plate dividing machine are as follows:
氣動鍘刀式zhi分板機性能特點：
The performance characteristics of the pneumatic chopper type Zhi plate splitter are as follows
1.裁切率為dao1秒/1分割，由腳踏板氣動開關控制.
The cutting rate is Dao 1s / 1, which is controlled by foot pedal pneumatic switch
2.裁切刀組為被動啟動，可安全掌握裁切線及位置;裁切應力小，不易形成龜裂現象
The cutter group is passively activated, which can safely control the cutting line and position; the cutting stress is small, and it is not easy to form cracking phenomenon
3.非滾輪(輪刀，走刀)式裁切，無粉塵現象，無馬達驅動，無碳粉污染.
No dust, no motor drive, no carbon powder pollution
4.非磨擦式切削，無刀具金屬殘留.
Non friction cutting, no tool metal residue
5.刀片使用200000/次無電力供應，故無電器產品損耗，更換之情.
Blade used 200000 times, no power supply, no loss of electrical products, replacement
6.刀具由進口公司自行設計，無須進口時效大
The cutting tool is designed by the import company, so it is not necessary to import it and has a long time effect
7.使用4-5KG的空壓，無須特定切割場所;外觀以防銹保養油擦拭即可。
Use 4-5kg air pressure, do not need special cutting place; the appearance can be wiped with antirust maintenance oil.
氣動鍘刀式分板機的操作的安全注意事項：
Safety precautions for operation of pneumatic cutter type plate splitter:
1，作業前先確認機械是否正常。在正式的開始工作前，首先要讓機械試運轉二分鐘左右，看刀具上下運動，電路，氣路等是否順暢，一定確認OK后再開始工作。
Confirm whether the machinery is normal before operation. Before the formal start of work, first of all, let the machine run for about two minutes to see whether the tool moves up and down, whether the circuit and air circuit are smooth, and then start to work after confirming that it is OK.
2，嚴格按作業指導書作業，安全事故一般都是由于工作人員不規范的操作引起的，所以說使用氣動鍘刀式鋁基板/PCB/LED分板機一定要注意操作的規范性。
Work in strict accordance with the operation instructions, safety accidents are generally caused by the non-standard operation of the staff, so the use of pneumatic knife type aluminum substrate / PCB / LED board splitter must pay attention to the standardization of operation.
3，加強工業生產的安全意識。要時時加強安全第一的工作目標，不然工作再努力，身體受到了損傷，也是得不嘗失。
Strengthen the safety awareness of industrial production. We should always strengthen the work goal of safety first, otherwise, if we work hard, we will not lose our health.
4，加工時要使PCB板的V槽與直刀刀口對準對齊，這樣分出來的板毛邊少，刀具的磨損量也少，效率也提高了好多。
During processing, the V-groove of PCB board should be aligned with the edge of the straight knife, so as to reduce the board burr, reduce the tool wear, and improve the efficiency.
5，作業時不能將手指或其它物品放在兩直刀中間。由于直刀的鋼材是很鋒利的，因此加工時手指或是其它雜物注意要與刀片保持一定的距離。
Do not put fingers or other objects between two straight knives during operation. As the steel of the straight knife is very sharp, it is necessary to keep a certain distance between the finger and the blade when processing.
