分板機通常是指baiPCB分板機，也就是線du路板分板機zhi。分板機被dao廣泛應用于電子產品制造業回。由于傳統的人答工折板方式會有很強的應力產生，對產品品質造成嚴重影響，所以人工折板已基本上被機器分板所取代。 分板機可分以下幾種：
The board dividing machine usually refers to the baipcb board dividing machine, namely the line Du road board dividing machine. The board splitter is widely used in electronic products manufacturing industry. Due to the strong stress produced by the traditional manual folding method, which has a serious impact on the product quality, the artificial folding plate has been basically replaced by the machine. The dividing machine can be divided into the following types:
1、走刀式分板機，Knife type plate splitter
2、沖壓式分板機，Stamping plate splitter
3、銑刀式分板機，Milling cutter type plate splitter
4、激光分板機、Laser splitter
5、鍘刀式分板機。 Chopper type plate splitter
以上四種分板機的優缺點：
The advantages and disadvantages of the above four kinds of plate splitters
1、走刀式分板機 優點：成本低 缺點：只能進行直線分板。有毛邊。
Advantages: low cost, disadvantages: can only carry out linear plate. It has a rough edge.
2、沖壓式分板機 優點：首次投入成本低，速度快。缺點：由于必須專板專模，后期成本高。有應力
Advantages: low cost and high speed for the first time. Disadvantages: due to the special plate and mold, the later cost is high. With stress
3、銑刀式分板機 優點：可進行任意形狀分板，應力很小，切割邊緣無毛邊。缺點：首次成本較大。
Advantages of milling cutter type plate dividing machine: it can divide plates of any shape, with small stress and no burr on cutting edge. Disadvantages: high cost for the first time.
4、激光分板機 優點：同時具備銑刀式分板機的優點，并可對PCB板進行微分切，無應力。 缺點：機器價格昂貴。
Advantages of laser plate splitter: it has the advantages of milling cutter type plate splitter at the same time, and can perform differential cutting on PCB board without stress. Disadvantages: the machine is expensive.
5、鍘刀式分板機 優點：純氣動(工廠常用氣壓即可),體積小巧(桌面式),出力大,可切任意寬度厚度的鋁基板,性價比高.
Advantages: pure pneumatic (factory air pressure can be used), small size (desktop type), large output, can cut aluminum substrate of any width and thickness, high cost performance
